SORT BY:

LIST ORDER
THREAD
AUTHOR
SUBJECT


SEARCH

IPS HOME


    [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

    RE: FW: iSCSI: "conservative reuse" requirement



    If you don’t want to define it, then you should not use it.

     

    There is an “endpoint” that represents the SCSI Initiator Port. If that “endpoint” can you just give that “endpoint” a term?

     

    Eddy

     

    -----Original Message-----
    From: KRUEGER,MARJORIE (HP-Roseville,ex1) [mailto:marjorie_krueger@hp.com]
    Sent: Wednesday, January 02, 2002 1:06 PM
    To: 'Eddy Quicksall'; Jim Hafner
    Cc: ips@ece.cmu.edu
    Subject: RE: FW: iSCSI: "conservative reuse" requirement

     

    Did you read Jim's response carefully?  You repeat the statement "It (initiator portal group" is an important item to define (as mapping to the SCSI Initiator Port). It is what is needed for persistent reservations. Defining it properly will eliminate the need for the "conservative reuse" clause." and Jim has explained to you that this statement is incorrect.  Several of us have given you the definition of initiator portal group and you still have this misconception.  I don't know how putting the definition in the draft would clear up your misunderstanding?

     

    If "initiator portal group" is not explicitly defined in the draft, it is in part because that concept plays no part in the iSCSI protocol - it's very important that you understand that.  In order for an initiator to connect to a target, the initiator must know the target's portal groups.  The converse is NOT true - nothing external to the target that participates in the iSCSI protocol needs to know the initiator's address information.  Perhaps if you let go of the idea that the initiator portal group is an important thing in the iSCSI protocol, you'll understand what has been explained?

    Marjorie Krueger
    Networked Storage Architecture
    Networked Storage Solutions Org.
    Hewlett-Packard
    tel: +1 916 785 2656
    fax: +1 916 785 0391
    email: marjorie_krueger@hp.com

    -----Original Message-----
    From: Eddy Quicksall [mailto:Eddy_Quicksall@ivivity.com]
    Sent: Wednesday, January 02, 2002 5:12 AM
    To: Jim Hafner
    Cc: ips@ece.cmu.edu
    Subject: RE: FW: iSCSI: "conservative reuse" requirement

    I see I must have offended you. I didn't mean to do that ...

     

    I was referring to the definition of iSCSI Initiator Portal Group and that it has been left out. It is an important item to define (as mapping to the SCSI Initiator Port). It is what is needed for persistent reservations. Defining it properly will eliminate the need for the "conservative reuse" clause.

     

    The problem I saw was that many people have misunderstood the ISID and how it should be used to be compliant with SAM-2.

     

    I said much earlier that the definition of iSCSI Initiator Portal Group was implied and that is exactly what you have pointed out below.

     

    It seems so silly not to define it. Can you give me a reason why it should not be defined?

     

    Eddy

     

    -----Original Message-----
    From: Jim Hafner [mailto:hafner@almaden.ibm.com]
    Sent: Tuesday, January 01, 2002 4:16 PM
    To: Eddy Quicksall
    Cc: ips@ece.cmu.edu
    Subject: RE: FW: iSCSI: "conservative reuse" requirement

     



    Eddy,

    I don't know why you think we've done a bad job of defining these terms. I don't have a copy of the draft around at the moment but this is my recollection:

    These are the iSCSI architectural level components:
    There is a definition of an iSCSI node (that has a WWU name).

    There is a definition of Portal Group (which does NOT apply only to targets but is applicable to both targets and initiators). (I even thought there was text that said that this definition applied to both initiator and target, but I could be wrong about this.)

    There is a definition of sessions and the specification of how SSIDs are generated from the ISID component and the TSID component.


    There is the (required by any SCSI protocol) a mapping of the SCSI constructs to iSCSI constructs. The SCSI constructs of concern here are (a) device -- both initiator and target (b) port -- initiator, target and initiator/target and (c) nexus:

    There is explicit language that defines the SCSI device as a component of an iSCSI node (and that there is only one such SCSI device construct within an iSCSI node -- and this allows us to define the SCSI device name as equal to the iSCSI node name).

    There is explicit language that maps the SCSI initiator port to an iSCSI construct and *different* language that maps the SCSI target port to an iSCSI construct. For the SCSI initiator port, the mapping is to the initiator end of a session. For the SCSI target port, the mapping is to the iSCSI target portal group. It is NOT symmetric and is stated so explicitly.

    There is explicit language the maps the SCSI nexus to the session. Note that a nexus is a relationship between a SCSI initiator port and a SCSI target port (that's the SAM definition!). What iSCSI does is map this relationship from the iSCSI initiator end of a session (SCSI initiator port) to the iSCSI target portal group (SCSI target port).

    Does the text not say this?

    Note that the approach we've taken here is to define the iSCSI architecture and then MAP the iSCSI constructs to SAM-defined SCSI constructs.

    And, an attempt to map SCSI initiator port to the iSCSI initiator portal group (as you suggest) will force a requirement that there can be only one session between an iSCSI initiator portal group and an iSCSI target portal group! If one thinks that most "portal groups" will be instantiated by an iSCSI HBA, then this requirement is unacceptable.


    Jim Hafner

    Sent by: owner-ips@ece.cmu.edu

    To: John Hufferd/San Jose/IBM@IBMUS
    cc: ips@ece.cmu.edu
    Subject: RE: FW: iSCSI: "conservative reuse" requirement



    My problem is that we have not done a good job of defining the iSCSI
    Initiator Portal Group in the spec. If defined correctly, there should be no
    need for the "conservative reuse" clause.

    Here is how I think it should be defined ... SCSI Initiator Port: this maps
    to an iSCSI Initiator Portal Group.

    You could go on to say something like Marjorie said below ... that it is a
    collection of IP addresses that can be used to support one or more iSCSI
    sessions.

    Given that it is equivalent to a SCSI Initiator Port and that it is
    identified by the InitiatorName+ISID, it follows that every session from
    that "port" would have to use the same ISID; and that is what will make
    persistent reservations work.

    It is not that "conservative reuse" won't work ... it is more that it is
    hard to explain because we don't have a clear definition of a SCSI Initiator
    Port and Initiator Port Identifier.

    Eddy

    -----Original Message-----
    From: John Hufferd [mailto:hufferd@us.ibm.com]
    Sent: Monday, December 31, 2001 8:01 PM
    To: Amir Shalit
    Cc: ips@ece.cmu.edu
    Subject: RE: FW: iSCSI: "conservative reuse" requirement


    We overtly chose NOT to identify an ISID with a TCP/IP address, since the
    ISID may span several HBAs and/or TCP/IP addresses.  It was more general
    and consistent NOT to be tied to a  TCP/IP address.

    .
    .
    .
    John L. Hufferd
    Senior Technical Staff Member (STSM)
    IBM/SSG San Jose Ca
    Main Office (408) 256-0403, Tie: 276-0403,  eFax: (408) 904-4688
    Home Office (408) 997-6136, Cell: (408) 499-9702
    Internet address: hufferd@us.ibm.com


    "Amir Shalit" <amir@astutenetworks.com>@ece.cmu.edu on 12/31/2001 03:35:56
    PM

    Sent by:    owner-ips@ece.cmu.edu


    To:    "Eddy Quicksall" <Eddy_Quicksall@ivivity.com>, "KRUEGER,MARJORIE
          \(HP-Roseville,ex1\)" <marjorie_krueger@hp.com>, Jim
          Hafner/Almaden/IBM@IBMUS
    cc:    "ips@ece. cmu. edu \(E-mail\)" <ips@ece.cmu.edu>
    Subject:    RE: FW: iSCSI: "conservative reuse" requirement



    Marjorie,

    If an "initiator/target portal group" concept is
    "the collection of IP addresses which can be combined to create a single
    iSCSI session."
    why isn't it defined as such in the draft?

    IMO, it would have been better to define ISID/TSID in simple networking
    terms
    like {TCP/IP address + Name} instead of coming up with network entity,
    network portal
    and portal group terminology.

    Amir


    -----Original Message-----
    From: owner-ips@ece.cmu.edu [mailto:owner-ips@ece.cmu.edu]On Behalf Of
    Eddy Quicksall
    Sent: Monday, December 31, 2001 2:15 PM
    To: KRUEGER,MARJORIE (HP-Roseville,ex1); Jim Hafner
    Cc: ips@ece. cmu. edu (E-mail)
    Subject: RE: FW: iSCSI: "conservative reuse" requirement


    Marjorie,

    If "an initiator portal group is the same concept as the target portal
    group", then it must be equivalent to the SCSI Initiator Port (because we
    have said that the SCSI Target Port maps to an iSCSI Target Portal Group).

    Comments?

    Eddy

    -----Original Message-----
    From: KRUEGER,MARJORIE (HP-Roseville,ex1) [mailto:marjorie_krueger@hp.com]
    Sent: Monday, December 31, 2001 4:48 PM
    To: 'Eddy Quicksall'; Jim Hafner
    Cc: ips@ece. cmu. edu (E-mail)
    Subject: RE: FW: iSCSI: "conservative reuse" requirement

    Your assumption of what is meant by an initiator portal group is incorrect
    (I don't think it's implied that IPG = IP???)  An initiator portal group is
    the same concept as a target portal group - it's the collection of IP
    addresses which can be combined to create a single iSCSI session.
    Frequently this is thought of as an iSCSI HBA, but that is not necessarily
    so, it could be a number of iSCSI HBAs, etc.

    Marjorie Krueger
    Networked Storage Architecture
    Networked Storage Solutions Org.
    Hewlett-Packard
    tel: +1 916 785 2656
    fax: +1 916 785 0391
    email: marjorie_krueger@hp.com

    > -----Original Message-----
    > From: Eddy Quicksall [mailto:Eddy_Quicksall@ivivity.com]
    > Sent: Monday, December 31, 2001 10:39 AM
    > To: Jim Hafner
    > Cc: ips@ece. cmu. edu (E-mail)
    > Subject: RE: FW: iSCSI: "conservative reuse" requirement
    >
    >
    > Regarding answer 2 below:
    > There is no given definition for an iSCSI Initiator Portal Group
    (however,
    > it is implied to be the same as the endpoint in 9.1.1, which would be the
    > same as the SCSI Initiator Port). Since an iSCSI Initiator Portal Group
    is
    > the same as a SCSI Initiator Port and since an iSCSI Target Portal Group
    is
    > the same as a SCSI Target Port, then each session in answer number 2
    would
    > not have a "different SCSI initiator port"; hence you would have a
    parallel
    > nexus.
    > One thing that is not clear in section 9.1.1 (however, it is loosely
    > implied) is that the reuse of ISID's applies to a given initiator
    endpoint
    > (SCSI Initiator Port or what should be called an iSCSI Initiator Portal
    > Group)). I think that should be made clear.
    > What am I missing? Could it be that an iSCSI Initiator Portal Group is
    not
    > equivalent to a SCSI Target Port?
    >
    > Eddy
    >
    > -----Original Message-----
    > From: Jim Hafner [mailto:hafner@almaden.ibm.com]
    > Sent: Saturday, December 29, 2001 6:14 PM
    > To: Eddy Quicksall
    > Cc: ips
    > Subject: RE: FW: iSCSI: "conservative reuse" requirement
    >
    >
    > Eddy,
    >
    > The SCSI initiator port is modeled as the endpoint of the
    > iSCSI session;
    > the SCSI target port is modeled as the iSCSI target portal group.  The
    > reason we did it this way was to allow more than one session
    > between portal
    > groups by allowing multi-plexing of sessions with different
    > ISIDs from the
    > same iSCSI initiator portal group to the same target portal group.
    >
    > So, the answer to your questions are:
    > 1) no, we're assuming no more than on session *with the same
    > ISID* to the
    > same target portal group (that'd be more than one nexus), but
    > by allowing
    > different ISIDs we get different SCSI initiator ports.
    > 2) no, we're allowing more than one session between an iSCSI initiator
    > portal group and an iSCSI target portal group (each session
    > has a different
    > SCSI initiator port (id'ed by its ISID) but the same SCSI target port
    > (id'ed by its portal group tag).
    > 3) sort of, the ISID together with the iSCSI Initiator Name fully
    > identifies the SCSI initiator port (and so defines the SCSI
    > initiator port
    > name and the identifier).
    >
    > Does that clear this up?
    >
    > Jim Hafner
    >
    >
    > "Eddy Quicksall" <Eddy_Quicksall@iVivity.com> on 12/28/2001
    > 07:19:33 PM
    >
    > To:   Jim Hafner/Almaden/IBM@IBMUS
    > cc:   "ips@ece. cmu. edu \(E-mail\)" <ips@ece.cmu.edu>
    > Subject:  RE: FW: iSCSI: "conservative reuse" requirement
    >
    >
    >
    > Due to 2.5.3 (b) "Between a given SCSI initiator port and SCSI target
    > port, there can be only one I_T nexus (session)", aren't we always
    > "assuming no more than one session"?
    >
    > Or are you talking about more than one session between different SCSI
    > initiator ports and a single SCSI target port?
    >
    > Is the ISID equivalent to SAM-2's Initiator Port Identifier?
    >
    >
    > Eddy
    >
    > -----Original Message-----
    > From: Jim Hafner [mailto:hafner@almaden.ibm.com]
    > Sent: Friday, December 28, 2001 12:15 PM
    > To: John Hufferd; Eddy Quicksall; Mallikarjun C.; Black_David@emc.com
    > Cc: ips@ece.cmu.edu
    > Subject: Re: FW: iSCSI: "conservative reuse" requirement
    >
    >
    > Folks,
    >
    > Sorry for taking so long to jump into this discussion.
    >
    > There are a number of issues raised in this thread:
    > 1) should "conservative reuse" of ISIDs be made a MUST
    > 2) does "conservative reuse" imply that all hosts look "single SCSI
    > ported"
    >
    > Here's my two cents (using "CR" as a shorthand for "conservative
    > reuse")
    >
    > I don't believe that CR needs to be a MUST.  The only time this has
    > any
    > real value is in configurations that use SCSI persistent reservations
    > (and
    > where new SCSI target reservation features are enabled -- NB.  these
    > features are yet to be approved but are working their way through the
    > process). I don't think these are going to be (even in the future) the
    > majority of installations.  There are many ways then that CR could be
    > something that is not generally available in most drivers but is added
    > by
    > configuration and perhaps even "value add" (:-{)).
    >
    > In short, I don't see a strong case for this to be a MUST.  So, to
    > David
    > Black, my answer is that having a mechanism to enable this feature or
    > have
    > it as a "purchase requirement" is an acceptable mechanism to make sure
    > the
    > feature is there when needed, but it is need not be a requirement of
    > the
    > protocol.  To Mallikarjun, I think I'm agreeing with you that so long
    > as
    > there is a mechanism defined, iSCSI has done it's job.
    >
    > As for the second issue (raised by Mallikarjun), let's look at the
    > definition of CR.  What is means is that when an iSCSI initiator
    > (node)
    > creates ISIDs for use in session identifiers, it attempts to reuse
    > them
    > as
    > much as possible with different SCSI target ports (iSCSI target portal
    > groups).  This is the only way that a SCSI target or LU can see the
    > same
    > SCSI initiator port through two or more of its SCSI target ports --
    > that
    > is, that the target can determine multiple paths *from* the same SCSI
    > initiator port.   But, the model for generating ISIDs is not really at
    > the
    > node level but at the initiator portal group level.
    > So, IMO, the conclusion that all hosts must then look "single SCSI
    > ported"
    > is too dramatic.  As I mentioned,  ISIDs are conceptually generated
    > within
    > initiator portal groups (that's why we defined the mechanism for
    > generating
    > ISIDs).  The conclusion I draw is that (assuming no more than one
    > session
    > to any given target portal group), an iSCSI initiator implementing CR
    > will
    > have as many SCSI initiator ports as iSCSI initiator portal groups
    > (independent HBAs?).  Each initiator portal group would generate one
    > ISID
    > (that is different from that generated by/for the other initiator
    > portal
    > groups) and use CR for repeatability.  [This is consistent with a
    > model
    > that mapped SCSI initiator ports to initiator portal groups, which we
    > had
    > to abandon because the "assuming no more than one session..." was no
    > acceptable as a requirement!!!]  This independence of ISIDs for each
    > initiator portal group allows each initiator portal group to open
    > sessions
    > with *every* target portal group it knows about without having to
    > worry
    > about interfering with other sessions. [This has shades of the
    > "partitioning" rule for ISIDs that has been discussed ad nauseum!!!]
    >
    > (I have a feeling that this note is not well composed -- it is the
    > holidays, you know).  I hope I've addressed everyone's concerns and we
    > can
    > lay this one to rest.
    >
    > Jim Hafner
    >
    >
    > John Hufferd
    > 12/25/2001 08:49 AM
    >
    > To:   "Eddy Quicksall" <Eddy_Quicksall@iVivity.com>
    > cc:   Jim Hafner/Almaden/IBM@IBMUS
    > From: John Hufferd/San Jose/IBM@IBMUS
    > Subject:  Re: FW: iSCSI: "conservative reuse" requirement  (Document
    > link:
    >       Jim Hafner)
    >
    > You are correct.  The section was created by Jim Hafner, and via this
    > note
    > I will ask him if he could answer Mallikarjun Directly since I did not
    > understand his issue.
    >
    > .
    > .
    > .
    > John L. Hufferd
    > Senior Technical Staff Member (STSM)
    > IBM/SSG San Jose Ca
    > Main Office (408) 256-0403, Tie: 276-0403,  eFax: (408) 904-4688
    > Home Office (408) 997-6136, Cell: (408) 499-9702
    > Internet address: hufferd@us.ibm.com
    >
    >
    > "Eddy Quicksall" <Eddy_Quicksall@iVivity.com> on 12/24/2001 06:06:44
    > PM
    >
    > To:   John Hufferd/San Jose/IBM@IBMUS
    > cc:
    > Subject:  FW: iSCSI: "conservative reuse" requirement
    >
    >
    >
    > John,
    >
    > Were you the author of "conservative reuse"? I am wondering about some
    > issues. Maybe you could educate me somewhat ...
    >
    > I started this subject in a different thread by saying that it may be
    > good to make "conservative reuse" a MUST.
    >
    > I got one objection from Santosh below. Then David Black picked it up
    > by basically agreeing with me. Then Mallikarjun objected to that.
    >
    > It seems like the objective would be to give targets a way to figure
    > out that two or more sessions are coming from the same Initiator Port.
    > That is needed support persistent reservations.
    >
    > If an initiator does not use "conservative reuse", I don't think
    > targets will be able to make that determination.
    >
    > Comments?
    >
    > Eddy
    >
    > -----Original Message-----
    > From: Mallikarjun C. [mailto:cbm@rose.hp.com]
    > Sent: Monday, December 24, 2001 12:47 AM
    > To: Black_David@emc.com
    > Cc: ips@ece.cmu.edu
    > Subject: Re: iSCSI: "conservative reuse" requirement
    >
    > > I think this is headed towards "conservative reuse" being a MUST if
    > > we're serious about support for shared persistent reservations.
    >
    > Mandating "conservative reuse" appears to force initiators to always
    > act
    > as a single initiator port (wrt one target; assuming only one session
    > as
    > an
    > example) per initiator device - which rules out the case of an
    > initiator
    >
    > intentionally wanting to present a different port to each target
    > portal
    > group.
    >
    > IMHO, if iSCSI provides an architected mechanism to support shared
    > persistent reservations ("conservative reuse"),  that should be
    > completely
    > adequate to meet the expectations to be a legal SCSI protocol.
    > --
    > Mallikarjun
    >
    > Mallikarjun Chadalapaka
    > Networked Storage Architecture
    > Network Storage Solutions Organization
    > Hewlett-Packard MS 5668
    > Roseville CA 95747
    >
    > ----- Original Message -----
    > From: <Black_David@emc.com>
    > To: <santoshr@cup.hp.com>
    > Cc: <ips@ece.cmu.edu>
    > Sent: Friday, December 21, 2001 4:50 PM
    > Subject: iSCSI: "conservative reuse" requirement
    >
    >
    > > Santosh Rao writes:
    > >
    > > > I am opposed to the suggestion that "conservative re-use" of ISIDs
    > be
    > > > made a MUST. This is really only required when initiators need to
    > be
    > > > using the new T10 Reservation scheme that can be shared
    > > > across initiator ports.
    > >
    > > Those reservations are a Target feature.  With this approach, the
    > ability
    > > to use the target feature depends on details of the initiator
    > > implementation.
    > > More below ...
    > >
    > > > For those initiators that don't care about this type of
    > reservation,
    > > > conservative re-use is of no use and initiators may like to assign
    > > > ISID's in a per-initiator node fashion, thereby, being able to use
    > these
    > > > ISIDs as a lookup index for the sessions on that initiator node.
    > > >
    > > > Hence, I suggest that "conservative re-use" be worded as
    > > > "encouraged to use" or something to that effect, but not MUST USE.
    > > >
    > > > Comments ?
    > >
    > > The "initiator" is more than one entity.  The iSCSI HBA/NIC and
    > driver
    > > doesn't know whether shared persistent reservations are being used
    > and
    > > shouldn't have to care - they're just more SCSI commands to
    > transport.
    > > Some other entity (e.g., clustering software) will be generating the
    > > shared persistent reservations.  This raise the possible scenario
    > > involving a target that supports the new shared persistent
    > reservations
    > > and an entity that wants to use them.  The entity detects (via SCSI
    > means,

    > > e.g., something in a mode page) that the Target supports shared
    > persistent
    > > reservations, tries to use them, only to discover that they don't
    > work
    > > because the iSCSI HBA/NIC doesn't implement "conservative reuse".
    > >
    > > I'm worried about this causing both interoperability issues and
    > possible
    > > T10 issues -- from a T10 viewpoint, if shared persistent
    > reservations
    > > don't work, the initiating entity should have some SCSI-level means
    > > of determining this ... if that means exists only on the Target, the
    > > above scenario is iSCSI's problem (Target can't query Initiator to
    > > determine whether it does "conservative reuse"), and having a
    > separate
    > > initiator side means that the entity has to check only for iSCSI
    > (and
    > > not for any other SCSI transport) does not seem like the right
    > > approach.
    > >
    > > I think this is headed towards "conservative reuse" being a MUST if
    > > we're serious about support for shared persistent reservations.
    > >
    > > Comments?
    > > --David
    > > ---------------------------------------------------
    > > David L. Black, Senior Technologist
    > > EMC Corporation, 42 South St., Hopkinton, MA  01748
    > > +1 (508) 249-6449 *NEW*      FAX: +1 (508) 497-8500
    > > black_david@emc.com         Cell: +1 (978) 394-7754
    > > ---------------------------------------------------
    > >
    > >
    >
    >
    >






Home

Last updated: Wed Jan 02 15:17:45 2002
8249 messages in chronological order